Brick Paver Installation & Edging



Staging of product

Many paver tasks will vary depending upon access, website conditions, job size and naturally, the weather. These scenarios can have a general influence on your task from a timing stand point. Cautious factor to consider needs to be taken to figure out the time to begin the paver installation. Always aim to avoid any traffic or decrease on the prepared locations.

The foreman or job manager must constantly have the materials (sand/ pavers) dispersed around the project site for simple and efficient setups. Paver pallets/bundles should be put in a way not to interfere with the paver installation. The correct pallet/bundle placement can make the actual job installation much easier and quicker by decreasing the total labor of handling the product.

Brick paver patterns

Pavers can be positioned in various patterns depending upon their shape. Each paver shape will typically have numerous different hatch patterns that are offered by the maker.

Contractors need to take into factor to consider the traffic weight loads on their paver projects. In a lot of applications around the world, it has been shown that pavers laid in a herringbone pattern have actually carried out adequately.

Pavers that are 60 mm (2 - 3/8 in) thickness appropriate for pedestrian applications. Pavers that are going to be utilized in commercial or industrial applications need to be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a number of conditions that identify the beginning point of a paver project.

When starting to install pavers it is best to snap a real straight chalk line on the surface of the bed linen sand or pull a true straight string line above the surface of the bed linen sand at the ended up elevation of the pavers This will assist as a guide for maintaining straight joint lines and will also enable the installer to make changes in the positioning of the pavers.

Buildings and concrete curbing are normally not straight and must not be utilized for developing straight joint lines. The usage of string lines is necessary to identify the real straightness of the edge. As the paver installation advances, the string lines will help minimize the need for small trim pieces.

These will maintain a minimum joint width and allow the bedding and jointing sand to go into between each paver. Pavers with spacer bars are normally not laid in snug versus each other considering that a string line will supply constant joint spacing.

Installation of brick pavers.

One of the most commonly used techniques for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have pulled or above the bedding sand. The best technique is to position a paver versus another one and let it move down into the bed linen sand.

When setting up pavers on a high grade, they must be set up at the base of the grade going uphill. This will avoid the pavers from sneaking as they are being laid.

On large industrial and industrial applications, hand laying pavers would not be cost effective due to the labor intensity. The best way for installing pavers on large tasks is to install them mechanically. Making use of a mechanical laying maker can set up around 6000 - 7000 sq ft a day. There are a couple products a professional ought to consider before installing pavers mechanically:

1.) Mechanical installers are only efficient in setting up pavers in specific patterns.

2.) The professional must make sure that the manufacturer can production and bundling pavers in the wanted pattern on the pallets for simple mechanical installation.

Poor color blending might result in an irregular looking installation. A lot of manufacturers are consistent with color blending on each bundle of pavers, however it is the professional's obligation to ensure correct mixing in the field.

Cutting procedures for brick pavers.

Specialists generally have two methods of cutting pavers. When cutting pavers wet, it will help decrease dust and will extend the diamond blades life. The operator of the brick saw ought to constantly cut the pavers away from the surface area of the paver field when cutting wet, due to the reality that the pavers will produce a slurry that will stain the paver surface.

The brick saw operator needs to always wear the correct security that is needed for running a saw, such as eye, ear, respiratory and hand defense ).

Edging types

Edge restraints play a significant role in the total success of an interlocking pavement Paver Installation Boca Raton installation Edging restraints get rid of lateral movement of the pavers and hold the pavers securely together. Particularly at the outer boundary of the paver application, without an edging restraint, your project is ensured to fail with time.

There are a number of different edging restraints from which contractors can select. Typically made edge restraints are the most commonly utilized by professionals. Made edging restraints can range from, plastic edging, steel and aluminum, lumbers or precast concrete and stone. An edging type that is used mostly in industrial and industrial applications is poured-in-place concrete curbs. This edging restraint is usually installed by other professionals.

Edging installation.

When installing your edge restraint, it ought to rest straight on top of the compacted gravel base. The compressed gravel base course should extend a minimum of 6in beyond the border of the pavers This will provide an appropriate foundation upon which the edging restraint can sit. Produced edging (i.E. Plastic, steel or aluminum) should be securely anchored into the compressed gravel base( consult the maker's literature for the suggested spacing of the spikes). There are some edging restraints that will extend much deeper into the gravel base or beyond the base course (i.E. Timbers or poured-in-place curbs ). Edging restraints ought to never be put directly on top of the bedding sand. This might result in the migration of the bed linen sand and eventual lateral movement of the pavers. If there is a possibility of losing bed linen sand between the pavers and the edge restraint, then geo textile material is recommended. When a gap in between the pavers and the edging goes beyond 3/8" (10mm), then the space must be filled with cut pavers. All edging applications should be appropriately back filled after they are set up to help offer extra stability.

Compaction of brick pavers.

After installation, the pavers have to be compressed. The entire area that is to be compressed should be swept tidy of any foreign objects and debris that can trigger scuffing or scratching on the surface of the pavers.

It is essential to have a compactor that can apply between 3000lbs. And 5000 lbs. Of centrifugal compaction force. In addition, it is very important that the very first compaction takes place before any jointing sand has actually been applied to the pavers. This can trigger a bridging issue and will not allow the joints to be completely filled with jointing sand if jointing sand is used to the pavers prior to compaction takes location. This can also prevent the pavers from being appropriately set into the bed linen sand.

When compacting the pavers, it is advised that you make at least two passes in various instructions throughout the pavers. This will allow the pavers to be correctly embeded in the bed linen sand and will require the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is very crucial to the final efficiency of the pavers. Failure to do correct compaction can lead to deformations and pavement failure over time.


Paver pallets/bundles ought to be put in a way not to interfere with the paver installation. One of the most extensively utilized methods for the installation of pavers is hand installation of each paver. The operator of the brick saw ought to always cut the pavers away from the surface of the paver field when cutting damp, due to the reality that the pavers will develop a slurry that will stain the paver surface area. Edging restraints eliminate lateral movement of the pavers and hold the pavers tightly together. When a gap between the pavers and the edging surpasses 3/8" (10mm), then the area needs to be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *